MX

BIKES

FOOT

SIMULATOR

-

MX BIKES FOOT SIMULATOR -

Our MX BIKES Foot Sim is designed to be a plug and play controller for your FEET to give you real life functions of the shifting and braking within MX BIKES! No need to worry, steam allows multiple controllers to be configured and it is as easy as plugging the foot sim controller in and setting up your new (Shift up, Shift down, Rear Brake) keybinds within MX BIKES (Braking deadzone may need slight adjusting). This product is designed to be used with socks while seated in your gaming chair, then you rest your feet onto the pegs and pull it to a comfortable position for shifting and braking. DO NOT APPLY FULL BODY WEIGHT, OR FULL STRENGTH! This is only a controller, not a factory 125 you can and should abuse.

  • Our foot simulator is designed to be a controller that sits below your gaming chair and allows shifting and braking in game that will replicate the real life foot controls of a standard combustion engine dirtbike.

  • OUR MAIN POINTS OF FOCUS WHILE CREATING THIS PRODUCT WAS BASED AROUND DURABILITY AND RELIABILTY WHILE PROVIDING AN EASY, PLUG AND PLAY EXPERIENCE THAT REFLECTED SIMULATION LIKE FUNCTIONS TO A STANDARD COMBUSTION ENGINE DIRTBIKE FROM THE COMFORT OF YOUR EXISTING GAMING CHAIR.

    1. EXTRA DURIBILITY IN AND AROUND THE FOOT PEG AREA TO ALLOW A MAX LOAD OF 55LBS AT EACH PEG.

    2. RAISED LOWER FRAME FOR EXTRA GRIP AND CONTROL AT ANKLES WHILE THE SIMULATOR IS IN USE.

    3. 12MM X 30MM HEAVY DUTY COMPRESSION SPRINGS TO ALLOW FOR A SUFFICIENT AMOUNT OF RESISTANCE WHEN OPERATING THE FOOT SIMULATION FUNCTIONS.

    4. SHIFT & BRAKE SHAFT UPGRADED MATERIAL TO WITHSTAND THE CONSTANT TWISTING AND TORQUING OF THE SIMULATION OPERATIONS. (PA12-CF) a good general-use plastic with broad additive applications and is known for its toughness, tensile strength, impact strength and ability to flex without fracturE.

    5. BALL BEARINGS AT SHIFT & BRAKE SHAFT FOR SMOOTH AND CONSISTENT OPERATIONS.

    6. SHIFT & BRAKE LEVER ARE DESIGNED SO THAT IF OVER EXTENDED IT WILL MAX OUT AGAINST THE FRAME OF THE CONTROLLER BEFORE FAILURE CAN HAPPEN. IT IS ALSO DESIGNED SLIGHTLY OFF BALANCED SO IF AN OVER EXTENSION OF AN UPSHIFT HAPPENS THE ENTIRE FRONT OF THE CONTROLLER WILL LIFT TO HELP PREVENT FAILURE.

    7. M6 THREADED INSERTS AND FLOOR CUSHIONS TO ALLOW FOR A LEVEL, ELEVATED BASE.

    8. FRAME COMPONENTS MANUFACTURED USING PETG. PETG (polyethylene terephthalate glycol) is A STRONG, DURABLE, AND IMPACT-RESISTANT PLASTIC.

    9. M4 & M2 SCREWS TO TIE ALL OF THE INDIVIDUAL FRAME PETG COMPONENTS TOGETHER.

    10. SPECIAL CLIPS DESIGNED ON THE UNDERSIDE TO SECURE POWERA WIRED X BOX CONTROLLER ALONG WITH SECURING THE WIRES FOR NEAT AND CONCEALED WIRE MANAGMENT.

  • 4EA - M6 THREADED FLOOR CUSHIONS

    4EA - M6 THREADED INSERTS

    4EA - 8MM X 22MM X 7MM BALL BEARINGS

    3EA - 12MM X 30MM HEAVY DUTY SPRINGS

    14ea - M4 X 25MM SCREWS

    15EA - M2 X 10MM SCREWS

    FRAME COMPONENTS ARE MANUFACTURED IN PETG (polyethylene terephthalate glycol) is A STRONG, DURABLE, AND IMPACT-RESISTANT PLASTIC.

    SHIFT SHAFT AND BRAKE SHAFT ARE MANUFACTURED IN (PA12-CF) a good general-use plastic with broad additive applications and is known for its toughness, tensile strength, impact strength and ability to flex without fracture

  • LOOKING FORWARD INTO THE FUTURE WE WOULD LOVE TO IMPROVE ON THIS ORIGINAL DESIGN TO PROVIDE AN AS USER FRIENDLY AND FUNCTIONAL PRODUCT AS POSSIBLE. WE ARE ALSO IN THE R&D STAGES OF DEVELOPING A FUNCTIONAL UPPER HANDLE BAR SECTION THAT WILL SECURE TO YOUR GAMING DESK AND ALLOW YOU TO USE ALL OF THE FUNCTIONS NEEDED TO CONTOL YOUR IN GAME MOVEMENTS THAT THE FOOT SIM DOES NOT PROVIDE.

weight TEST DEMONSTRATING THE PEGS SUPPORTING 55 LB WEIGHTS.

VIDEO DISPLAYING THE SMOOTH AND CONSISTENT TORQUING OF THE FUNCTIONS WHILE BEING MAXED OUT AGAINST THE FRAME FREE OF FAILURE.

IMAGE TO DISPLAY THE POWERA XBOX CONTROLLER SECURED INTO ITS HOUSING ALONG WITH CLIPS THAT PROVIDE SECURE AND CONCEALED WIRE MANAGMENT.

Designed and manufactured in the usa.

using an additive manufaturing procrss with 3d printers we are able to design and manufacture our prodcuts in house without needing any external manufactures for assistance.